Filleting and filling

-
Spent a bit of time today filleting the false floor join.



I'm pretty happy with how they came out - cut of the end of a syringe to dispense a fairly thick mixture of 403 + Epoxy. Used the squeegee cut to a 85degree angle with the rounded corner to set the fillet. Worked out okay.

Mix was two pumps each 105+205 and three and a half heaped teaspoons of filler.

Used the left over mix to fill a few gaps around the edges of the deck.

Also cut out the slot for the centreboard. I'd marked out roughly where the slot was before gluing the floor and drilled a speculative hole in the middle to see if things had moved much - they hadn't.


Have a little more deck glue join filling to do (using a mix of epoxy and sawdust from the top layer of the ply) then going to make the gunwhales - probably out of maple but TBD up to the point I buy the wood. Will get an 8' foot length and scarf the outer lengths.

Comments

  1. TomFebruary 23, 2019 at 9:34 AM

    Planning on covering these with paint, if leaving exposed I'd have used 207 hardener to avoid yellowing.

    ReplyDelete

Post a Comment

Popular posts from this blog

Next round of improvements

-
Image
Had another sail, this time with some wind. Still not on the wire though (I blame my weight, well, also the wind). Almost capsized a couple of times due to slips, or messing up with the long tiller extension. Came back with a few more projects. My hands were weak after three hours of sailing, and my legs bruised (find myself kneeling a lot in lighter air). [ Done ] Rework outhaul so it doesn't rub against the vang [ Done ] Raise the trapeze rings so I can crouch/wire in lighter air [ Done ] Improve travel on the vang, I two blocked it at one point [ Done ] Add ratcheting block to the mainsheet system Add non skid to a couple of sections Seriously consider foam pads in areas on the deck! In general though my first set of improvements (mainly the new smaller lines!) worked well. Some of this is already done. New lines to the left below, old to the right. MUCH cleaner now! The new sleeve on the boom worked well, though it may need some reinforcements yet.
Read more

Upgrade to control lines

-
Image
One big annoyance from my first few sails has been the combination on continuous lines and rail mounted cleats. The cleats are uncomfortable to sit on and much worse kept coming uncleared. The main cause of uncleating being over exuberant use of the continuous lines pulling on the backside of the far cleats. Once the cleats on the rail are undone you have to reach them to recleat, likely a problem as your weight goes to the wrong place. Looking at rigging pictures I found images of Daryl’s Farr on face book where the cleats were centerline and led through eyes at the rail. This seemed to fix all my primary issues so I decided to copy.  Original layout: Removed and holes filled. Also marked out an extra area for more non skid: At this point I commented on Daryl’s picture and he replied that he no longer ran lines through the eyes, but instead to low friction rings on elastic. As I thought about this made a lot of sense as it would allow more control from outboard.
Read more

Repairing the rudder

-
Image
Having decided to repair the rudder step one was to get the main stock rebonded. To do this I embedded two pieces of spruce. Rather than sand down the prior paint I decided to just pull off the carbon skin. This pulled the top layer of the spruce too leaving it pitted and rough so I filled the whole top. With it looking like a rudder again I sawed it into two pieces.... This is in order to work towards the final aim of both restoring the shape and also making the foil a LOT stronger than it was before. Aims are: Remove that big hole. It was way too big! Instead bond the down-haul into a smaller hole. Turn the foil into an I beam with carbon cross sections Thicken up with carbon skin from plan 1 Cutting the foil in half was a prep step towards step 2. To finish up I added two layers of carbon with an ash strip (about 1/8" thick) to replace the wood removed in the cut. Hopefully can finish up fairing tomorrow and get the foil skinned
Read more

Album